![]() In all cases stated above, contact customer support for immediate assistance. If your recteq is successfully running past 300° then we can be certain that all your components are properly functioning: Reaching maximum temperatures typically comes down to two major factors: fuel and air. Rapidly lowering the temp and opening the lid will cause severe temperature swings. Avoid setting the grill to a higher temp than your desired set-point to cheat out a faster start. Starting 15-20 minutes earlier than you anticipated will not cause any significant loss through pellet consumption. ![]() Remember, your recteq is an extremely efficient machine. The grill must constantly fight against the cold outside air.In cold weather that steel will take some time to warm up, causing slower startup. The recteq contains a large amount of heavy stainless steel.Here are a couple things to keep in mind: While the recteq can and will maintain excellent temperatures in even the coldest weather, it will take a little longer, and be a little more difficult in the cooler months to come up to temp. Weather – Even a perfect balance of air and pellets can’t account for extreme weather conditions. Remember, air’s ability to escape is crucial to high and consistent temperatures.Ĥ. Clean the lip of lid and all other areas of ventilation.Dust can settle at the bottom of the hopper and keep your grill from feeding a steady stream of pellets. Let your hopper run empty after 5-6 bags.Clean your firepot often to keep the air-holes clear.Always store pellets properly before use.Avoid wood blends that include Alder, Mesquite, and Charcoal.Use only Food Grade, 100% Premium Hardwood Pellets.Avoid using pellets that are older than 6 months.Look for a bright sheen on the outside of the pellet.Ensure that the bag is not dusty and broken down.Make sure your pellets are no longer than one and a half inches.Some wood pellets produced for heating fuel have a high content of softwood which can include pitch and should not be used for cooking. Pellet quality as well as how they are stored, and their age play a huge role in making sure that you are getting to temperatures on time. With proper care and maintenance, your grill will provide you years of trouble-free operation. Pellets – Using the right pellet is just as important as air flow. Using it on the left will cause interference with the RTD.Ģ. Make certain that if you are using a Sear Kit, that you are using it on the right-hand side of the grill.Ensure that the RTD probe is not touching the wall.Do not extend or modify areas of ventilation.If using foil, make sure the foil is not hanging over air channels.Clean the firepot regularly to keep air-holes clear.Ensure all areas of ventilation are clear of obstruction.Air Flow – Proper air flow is one of the single most important factors in achieving high temperatures. If you feel your recteq is taking longer than it should, here are some possible reasons why:ġ. However, there are several things that may cause your recteq to start and climb slower than intended. Startup and achieving precise temperatures may take 20-30 minutes in some cases. Keep in mind that pellet grills must start, nurture, and precisely control a live wood-fire. All recteq auger motors are single speed.If you are new to pellet grilling, there may be an adjustment period when it comes to start-up times. Furthermore, Feed Rate does in no way affect how fast or slow the auger turns. Changing the setting can and will affect the way the grill operates. NOTE: No settings should be adjusted outside of the factory set parameters, until you first speak with a recteq Customer Service Associate. Pressing the Temp Display button continuously will cycle between these three screens in a loop.(Meat Probe ranges are +10 and – 10) Use the Up and Down arrows to adjust all the settings. Press Temp Display again and the red light will move to Meat, this is the Meat Probe Calibration.(Offset ranges are +20 and – 20 but should never move from 0 unless advised by customer support) Press the Temp Display button and the red light will move over Actual.(The ranges of the minimum feed rate on the Bullseye Controllers are 5 – 250, however, they should never be set under 30 or over 65 without first talking with customer support) With the grill OFF, press and hold the Up Arrow and Temp Display at the same time until a number appears.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |